Ford Focus Service Manual: Fuel Vapor Tube Assembly
| Item | Part Number | Description |
|---|---|---|
| 1 | 9034 | Fuel tank filler pipe |
| 2 | W709393 | Fuel tank filler pipe bracket bolt |
| 3 | — | Fuel tank filler pipe bracket bolt (part of 9034) |
| 4 | — | Fuel tank filler pipe recirculation tube (part of 9034) |
| 5 | 9E857 | Evaporative Emission (EVAP) canister |
| 6 | — | Fuel vapor tube assembly-to-fuel tank filler pipe recirculation tube quick connect coupling (part of 9K164) |
| 7 | 9K164 | Fuel vapor tube assembly |
| 8 | — | Fuel Tank Pressure (FTP) sensor (part of 9K164) |
| 9 | 14A464 | FTP sensor electrical connector |
| 10 | — | Fuel vapor tube assembly-to-EVAP canister quick connect coupling (part of (9K164) |
| 11 | — | Fuel vapor tube assembly-to-fuel tank quick connect coupling (part of 9K164) |
| 12 | 9002 | Fuel tank |
Removal and Installation
WARNING: Do not
smoke, carry lighted tobacco or have an open flame of any type when working on or
near any fuel-related component. Highly flammable mixtures are always present and
may be ignited. Failure to follow these instructions may result in serious personal
injury.
WARNING: Do not
carry personal electronic devices such as cell phones, pagers or audio equipment
of any type when working on or near any fuel-related component. Highly flammable
mixtures are always present and may be ignited. Failure to follow these instructions
may result in serious personal injury.
WARNING: Always
disconnect the battery ground cable at the battery when working on an evaporative
emission (EVAP) system or fuel-related component. Highly flammable mixtures are
always present and may be ignited. Failure to follow these instructions may result
in serious personal injury.
- With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
- Disconnect the battery ground cable. For additional information, refer to Section 414-01.
- Disconnect the Fuel Tank Pressure (FTP) sensor electrical connector.
- Remove the RH rear wheel and tire. For additional information, refer to Section 204-04.
- Remove the retainers and the RH rear splash shield.
- Remove the 2 bolts from the fuel tank filler pipe brackets.
- To install, tighten to 11 Nm (97 lb-in).
- Disconnect the fuel vapor tube assembly-to-fuel tank filler pipe recirculation tube quick connect coupling. For additional information, refer to Section 310-00.
- Disconnect the fuel vapor tube assembly-to-Evaporative Emission (EVAP) canister quick connect coupling. For additional information, refer to Section 310-00.
- Disconnect the fuel vapor tube assembly-to-fuel tank quick connect coupling.
For additional information, refer to Section 310-00.
- Remove the fuel vapor tube assembly.
- To install, reverse the removal procedure.
- Carry out the Evaporative Emission System Leak Test. For additional information, refer to Evaporative Emission System Leak Test in this section.
Evaporative Emissions
NOTE: The vehicle emission vacuum routing diagrams are contained in
the Description and Operation subsection of the Engine Emissions Control section.
Refer to Section 303-08.
The Evaporati ...
Evaporative Emission Canister
Item
Part Number
Description
1
—
Vapor tube-to-Evaporative Emission (EVAP) canister quick connect coupling
(part of 9C047)
2
9E857
EVAP ...
More about Ford Focus:
Ford Focus Catalytic Converter
Removal
All vehicles
With the vehicle in NEUTRAL, position it on a hoist. For additional information,
refer to Section 100-02.
NOTICE: Do not excessively bend or twist the exhaust flexible pipe. Failure
to follow these instructions may cause damage to the flexible pipe.
...
