Ford Focus manuals

Ford Focus Service Manual: Oil Pump

Material
Item Specification
Motorcraft® Metal Surface Prep ZC-31-A
Motorcraft® SAE 5W-20 Premium Synthetic Blend Motor Oil (US); Motorcraft® SAE 5W-20 Super Premium Motor Oil (Canada) XO-5W20-QSP (US); CXO-5W20-LSP12 (Canada) WSS-M2C945-A
Motorcraft® Silicone Gasket and Sealant TA-30 WSE-M4G323-A4

Removal

  1. With the engine in NEUTRAL, position it on a hoist. For additional information, refer to Section  100-02.
  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the oil level indicator and tube. For additional information, refer to Oil Level Indicator and Tube in this section.
  1. Drain the engine oil, then install the drain plug.
    • To install, tighten to 28 Nm (21 lb-ft).
  1. Remove the 2 oil pan-to-bellhousing bolts.
  1. Remove the 2 bellhousing-to-oil pan bolts.
  1. Remove the 13 bolts and the oil pan.
  1. NOTE:

    Discard the gasket and clean and inspect the gasket mating surfaces.

    Remove the 2 bolts and the oil pump screen and pickup tube.

  1. Remove the oil pump drive chain tensioner.
    1. Release the tension on the tensioner spring.
    1. Remove the tensioner and the 2 shoulder bolts.

  1. Remove the chain from the oil pump sprocket.
  1. Remove the bolt and oil pump sprocket.
  1. Remove the 4 bolts and the oil pump.

Installation

  1. NOTE:

    Clean the oil pump and cylinder block mating surfaces with metal surface prep.

    Install the oil pump assembly. Tighten the 4 bolts in the sequence shown in 2 stages:

    • Stage 1: Tighten to 10 Nm (89 lb-in).
    • Stage 2: Tighten to 20 Nm (177 lb-in).

  1. Install the oil pump sprocket and bolt.
    • Tighten to 25 Nm (18 lb-ft).
  1. Install the chain onto the oil pump sprocket.
  1. Install the oil pump drive chain tensioner shoulder bolt.
    • Tighten to 10 Nm (89 lb-in).

  1. Install the oil pump chain tensioner and bolt. Hook the tensioner spring around the shoulder bolt.
    • Tighten to 10 Nm (89 lb-in).

  1. Install the oil pump screen and pickup tube and the 2 bolts.
    • Tighten to 10 Nm (89 lb-in).
  1. NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges, which make leak paths. Use a plastic scraping tool to remove traces to sealant.

    Clean all mating surfaces with metal surface prep.

  1. NOTE:

    If the oil pan is not secured within 10 minutes of sealant application, the sealant must be removed and the sealing area cleaned with metal surface prep. Allow to dry until there is no sign of wetness, or 10 minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.

    Apply a 2.5 mm (0.09 in) bead of sealant gasket and sealant to the oil pan.

    • Position the oil pan onto the engine and install the 2 rear oil pan bolts finger-tight.

  1. Using a suitable straight edge, align the front surface of the oil pan flush with the front surface of the engine block.

  1. Install the remaining oil pan bolts.
    • Tighten in the sequence shown to 25 Nm (18 lb-ft).

  1. Install the 2 bellhousing-to-oil pan bolts.
    • Tighten to 48 Nm (35 lb-ft).
  1. Install the 4 oil pan-to-bellhousing bolts.
    • Tighten to 48 Nm (35 lb-ft).
  1. Install the oil level indicator and tube. For additional information, refer to Oil Level Indicator and Tube in this section.
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Fill the engine with clean engine oil.
Oil Pump Screen and Pickup Tube
Removal With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section  100-02. Remove the oil pan. For additional information, refer to Oil Pan ...

Oil Pan
Material Item Specification Motorcraft® Metal Surface Prep ZC-31-A — Motorcraft® SAE 5W-20 Premium Synthetic Blend Motor Oil (US); Motorcraft® SAE 5W- ...

More about Ford Focus:

Ford Focus Safety Belt Maintenance
Inspection WARNING: All safety belt components must be inspected and corrected as part of any collision repair. Inspect all safety belt components as prescribed by Safety Belt Inspection and Repair After a Collision found in Section 501-20A General Procedures of this manual. Failure to fol ...

© 2016-2024 Copyright www.ffguide.net