Ford Focus manuals

Ford Focus Service Manual: Crankshaft Rear Seal with Retainer Plate

Ford Focus Service Manual / Powertrain / Engine / Engine Block / Seals and Gaskets / Crankshaft Rear Seal with Retainer Plate

Special Tool(s)

Installer, Crankshaft Rear Main Oil Seal 303-328 (T88P-6701-B1)

Material
Item Specification
Motorcraft® Metal Surface Prep ZC-31-A
Motorcraft® SAE 5W-20 Premium Synthetic Blend Motor Oil (US); Motorcraft® SAE 5W-20 Super Premium Motor Oil (Canada) XO-5W20-QSP (US); CXO-5W20-LSP12 (Canada) WSS-M2C945-A
Motorcraft® Silicone Gasket and Sealant TA-30 WSE-M4G323-A4
Motorcraft® Silicone Gasket Remover ZC-30

Removal

  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section  100-02.
  1. Remove the flywheel or flexplate. For additional information, refer to Flywheel or Flexplate in this section.
  1. Drain the engine oil.
    • Install the drain plug and tighten to 28 Nm (21 lb-ft).
  1. Remove the oil level indicator and tube. For additional information, refer to Oil Level Indicator and Tube in this section.
  1. NOTICE: If the oil pan is not removed damage to the rear oil seal retainer joint can occur.

    Remove the 17 bolts and the oil pan.

  1. Remove the 6 bolts and the crankshaft rear seal with retainer plate.

Installation

  1. Using the Crankshaft Rear Main Oil Seal Installer, position the crankshaft rear oil seal with retainer plate onto the crankshaft.

  1. Install the crankshaft rear seal with retainer plate and 6 bolts.
    • Tighten in the sequence shown to 10 Nm (89 lb-in).

  1. NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges, which make leak paths. Use a plastic scraping tool to remove traces of sealant.

    Clean and inspect all the oil pan, cylinder block and front cover flange mating surfaces.

  1. NOTICE: If not secured within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.

    NOTE:

    The oil pan must be installed and the bolts tightened within 4 minutes of applying the silicone gasket and sealant.

    Apply a 2.5 mm (0.10 in) bead of silicone gasket and sealant to the oil pan.
    • Install the oil pan and the 2 bolts finger-tight.

  1. Install the 4 front cover-to-oil pan bolts.
    • Tighten to 10 Nm (89 lb-in).

  1. Install the remaining oil pan bolts.
    • Tighten in the sequence shown to 25 Nm (18 lb-ft).

  1. Install the oil level indicator and tube. For additional information, refer to Oil Level Indicator and Tube in this section.
  1. Install the flywheel or flexplate. For additional information, refer to Flywheel or Flexplate in this section.
  1. Fill the engine with clean engine oil.
Crankshaft Front Seal
Special Tool(s) Installer, Camshaft Front Oil Seal 303-096 (T74P-6150-A) Remover, Oil Seal 303-409 (T92C-6700-CH) Material Item ...

Valve Cover
Material Item Specification Motorcraft® Metal Surface Prep ZC-31-A — Motorcraft® Silicone Gasket and Sealant TA-30 WSE-M4G323-A4 Valve Cov ...

More about Ford Focus:

Ford Focus License Plate Lamp - Removal and Installation
  Item Part Number Description 1 — License plate lamp screws (2 required) (part of 13550) 2 — License plate lamp lens (part of 13550) 3 13466 License plate lamp bulb 4 13550 License plate lamp 5 ...

© 2016-2024 Copyright www.ffguide.net